Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing happened? Glance within the tank, and you may see no water inside. Before you worry, rest assured that repairing this problem is usually easy to accomplish. If you can’t figure it out yourself, you can always arrange toilet repair with an experienced plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank.

Check the Water Supply

The first step is to verify that the water is turned on. If you or someone in your household recently did a toilet repair, you probably turned off the water first. Did you neglect to turn it back on? To check, turn the water shut-off valve on the wall in back of the toilet. If the valve was turned off, water ought to now start refilling the tank. If this does not work, test the water at your sink or an alternative plumbing fixture. If nothing spills out from the tap, you might have a larger water supply issue. Call your water company to find out more.

Reposition or Replace the Float Mechanism

Older toilet brands use a float ball to gauge the water level as it rises in the tank. When the ball reaches a certain height, the float arm it’s connected to stops the water flow. However, insufficient water may enter the tank if the ball is positioned wrong or the arm is damaged. To correct the float ball, start by removing the toilet tank lid. Bend the float arm up a little to adjust where it sits in the tank. If this doesn’t fix the problem, you might need to replace the entire float mechanism. You should be able to perform this yourself by following the instructions that come with the replacement parts, or you can employ a plumber for help. Just understand that float balls are old toilet systems. You may enjoy improved dependability and efficiency if you upgrade the existing tank components or replace the toilet altogether.

Adjust the Fill Valve

Newer toilets operate with a float cup rather than a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become blocked. Here are recommendations to attempt:

    • Modify the fill valve: Have a look inside the toilet and find the fill valve on top of a vertical tube device on the left side of the tank. Verify that it’s secure and evenly connected to the tube. Then, adjust the water level. Current models of toilets have an adjustment knob you can turn by hand, while older models may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to check the water level. Modify it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube.
    • Clean the fill valve: Mineral buildup and other crud might be covering the valve and keeping your toilet from filling. Shut down the water behind the toilet and take off the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to stop water from spraying everywhere. After several seconds, turn the water back off. Finally, wash the fill cap to dislodge any hard water buildup. If the cap is damaged, replace it.
    • Clean the valve tube: The tube below the fill valve may also be clogged. Shut off the water and take off the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on a little to flush away the debris. Replace the valve hardware and flush the toilet to test your work.

Repair or Replace the Trip Assembly

If you’ve attempted the steps above without success, the one remaining possibility is a broken trip assembly. This component links the flush handle to the tank. If it’s not working or positioned improperly, the flush cycle may not complete, leaving the tank bone dry. Detach the toilet tank lid and examine the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or broken, swap it with a new one. Whether you finish the job yourself or leave it to a plumber, this easy repair should get your toilet tank filled with water once again.

Schedule Toilet Repair Today

You can’t go long without a working toilet, so call [Company name] to request a toilet repair. We can figure out why your toilet isn’t filling and suggest the right fix. If your plumbing fixture is outdated and worn out, our team will install a high-efficiency toilet in your bathroom. Be assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule an appointment from one of our licensed crews, please contact your neighborhood Winnipeg Supply Service Experts office today.

Enjoy our blogs!

Keep checking back for more!